[email protected] | 50 Guohuai Road, Henan Province, China
We are a comprehensive steel machining service platform!
Home / Machining Projects / forged main shaft for wind turbine

forged main shaft for wind turbine

Machining Service: Cutting ServiceWelding ServiceBending ServiceRolling ServiceGrinding ServiceHeat TreatmentDrilling ServiceMilling Service

The mainshaftfor windpowergenerators, the largest part in the nacelle, is manufactured by casting or forging. The weight of the mainshaft, depending on the design, is generally 10 to 20 tons, and thus is significantly affected by the mass effect in cooling. In the present study, a cooling test was performed with a large specimen...

E-mail: [email protected]

GET THE PRICESEND MESSGAE

Metal Fabrication

Machining Equipment

Fabrication Equipment

34CrNiMo6 Wind Turbine Main Shaft Forging 6000T Open

High quality 34CrNiMo6 Wind Turbine Main Shaft Forging 6000T Open Die Hydropress from China, China's leading forging shaft product, with strict quality control rough forging factories, producing high quality rough forging products.

Missing:

wind turbine

Must include:

wind turbineforged main shaft for wind turbinemain shaft wind turbinewind turbine main shaft repairshaft in wind turbinewind main shaftvertical shaft wind turbinehigh speed shaft wind turbinewind turbine low speed shaftvertical shaft wind turbine designChina Crank Forged Roller Wind Turbine Main Shaft

China Customized Forged Wind Turbine Main Spindle forged main shaft for wind turbine

Forged Wind Turbine Main Spindle. The wind turbine main shaft is an important part of wind power equipment. We can produce spindles for various wind turbines of 1.5MW-2MW through special steelmaking, forging, heat treatment, machining and surface anti-corrosion treatment. Inquiry Chat NowChina Forging Steel Wind Turbine Main Shaft Factory and forged main shaft for wind turbineOur enterprise has a quality assurance system are actually established for Forging Steel Wind Turbine Main Shaft, Coolant Oil Pump 4m, Directional Machine N120 Repair Kit, Str Front Wheel Oil Seal 140x160x13,Fuwa Axle 20t Rear Wheel Oil Seal 136.5x200x20. We also ensure that your selection will be crafted with the highest quality and reliability.Fatigue and fracture mechanical behaviour of a wind forged main shaft for wind turbineJan 01, 2016Published by Elsevier B.V. Peer-review under responsibility of the Scientific Committee of ECF21. 21st European Conference on Fracture, ECF21, 20-24 June 2016, Catania, Italy Fatigue and fracture mechanical behaviour of a wind turbine rotor shaft made of cast iron and forged steel Jenni Herrmann *, Thes Rauerta, Peter Dalhoffa and Manuela forged main shaft for wind turbine

Forged Main Shaft for Wind Turbine

Wind Turbine Forgings Guoguang Group is a professional forged part manufacturer and supplier in China. We offer wind turbine rotor shaft, forged parts in nuclear energy industry, forged parts in automotive industry, and more. In addition, calender machines are also available. Related Names.Main Shaft For Wind Turbine, China Main Shaft For Wind forged main shaft for wind turbineProduct Details Main Shaft For Wind Turbine 1. 1.The product Forging Shaft Parts 2. Material Carbon Steel, Alloy Steel, Stainless steel, carbon steel, C-Mn steel, alloy structure steel, alloyed tool steel, cold roll steel, steel for pressure vessel, carburizing steel, die steel, stainless steel and so on 3.Open Access proceedings Journal of Physics Conference May 15, 2019and forged materials regarding the fatigue and the remaining life of the rotor shaft. It is shown, that it is worthwhile to think about a material exchange for the forged rotor shaft. 1. Introduction The design of wind turbine main structures shall be examined concerning the fatigue strength to figure out weight-optimization possibilities.

Optimized cast components in the drive train of wind forged main shaft for wind turbine

Mar 29, 2021The main objective is the optimization of design possibilities for wind turbine rotor shafts. Therefore, a raw hollow rotor design shaft made of EN-GJS-400-18-LT chill cast is developed. The project partner Fraunhofer LBF investigates the cyclic The mainshaftfor windpowergenerators, the largest part in the nacelle, is manufactured by casting or forging. The weight of the mainshaft, depending on the design, is generally 10 to 20 tons, and thus is significantly affected by the mass effect in cooling. In the present study, a cooling test was performed with a large specimen of 42CrMo4, which is often used as the material for the mainshaft, to empirically obtain the hardenability from the surface. Since the hardenability is dependent on the size of the main shaft, for standardization, DEFORM and JMatPro software programs were used to predict the hardness on the cooling curve at different positions and the predicted results were compared with the experimental hardenability results. When the mass effect was considered, the strength was higher at a position closer to the surface and lower at a position closer to the core. These experimental results were expressed as a function of mechanical strength depending on the depth. An ANSYS structural analysis was performed to calculate the equivalent stress. The safety factor was compared between the case where the mass effect was considered and the case where the yield strength was constant over the entire specimen for a more accurate evaluation of the structural safety.Structural Safety Analysis of Main Shaft for Wind Power forged main shaft for wind turbineWas this helpful?People also askWhat kind of steel is a turbine shaft made of?What kind of steel is a turbine shaft made of?The shaft is made of high creep resisting Cr Mo-V steel forging while the shrunk fit disc are machined from high strength nickel steel forging. The blades on the integral disc are secured by T root fastening while on shrunk fit disc by fork foot fastening.Turbine Rotor and shaft coupling types on ECVVTurbine Shaft at Best Price in IndiaCall +91-8048718796. Contact Supplier Request a quote. Hydro Turbine Rotor Shaft. 250/ Kilogram Get Latest Price. Other Information , China Experts in Manufacturing and Exporting Wind turbine main shaft, Ductile cast iron pipe mould, castings and forgings

Wind Generator Shaft Forged Turbine Shaft products wind turbine forged shaft wind turbine forged shaft, wind turbine forged shaft forged main shaft for wind turbine

A wide variety of wind turbine forged shaft options are available to you, such as 3 years. You can also choose from new wind turbine forged shaft, as well as from spline, flexible, and gear wind turbine forged shaft, and whether wind turbine forged shaft is manufacturing plant, hotels, or

Contact Us

With a technical production and processing team, we will supply deep service for steel plates/pipes/coils. Please leave a message about you requirement. Our professional after-sales pernel will response you in 24 hours.

  • E-mail:[email protected]
  • Tel: 0086-13569929107
  • Address: 50 Guohuai Road, Henan Province, China

Get in Touch